Numerical control lathe is a high-precision and high-efficiency automated machine tool equipped with multi station turret or power turret. The machine tool has a wide range of processing performance and has played a good economic role in the mass production of complex parts. Inter operatio operator ad principes specificationes et conditiones utilizacionis CNC lathe attention debet.

Specificationes operationis CNC lathes

Reducientes accidentes operationis equipationis CNC non solum ab pluribus aspectis, quales management, process, training, supervision et inspectione prohibiri sunt. Base on years of experience in CNC and numerous case studies, the following regulations for preventing operation accidents of CNC machine tools are summarized, which can play a positive guiding role in preventing operation accidents:

1) Equatoria numerica supervisoris a personibus et machinis operati sunt, et equipa non operabitur ante qualificationes accipere.

2) Quando duo aut plures operantur equipamentum, negotiatum est et translatum opus, et multo prohibitum est mutare statum equipamenti sine consentio operatorum.

3) Operatores doctrinam negotiam suam aeternum fortitudinem facient et sententiam suam responsabilitatis meliora facient.

4) Prius priorem processationem partem, programma diligenter inspicetur et subiecetur testam processationis singulos phases antequam processatio automatic a exercitur.

5) Post modificationem programae et datorum, inspectio stricto effecta est, et primos gradus processionis sequitur.

6) Selection of coordinate origin and tool change point in programming must be safe and foolproof.

7) Reasonably select cutting parameters, such as speed, cutting amount, feed rate, etc., to prevent overloading of equipment.

8) Laborem vacuum inspecte, et illos cum forma vacuum nimis magna (aut nimis parva) praecepit.

9) Metodo et positio opus et propus clampionis rationale esse oportet, et clampionis potest adequate adjusti.

10) Instrumenta clampionis firma est et fidelis.

11) Attention and attention must be paid during operation to prevent collisions when manually moving the machine tool.

12) Si est abnormalitate aut collisio in equipento, statim nuntiari sunt servitutis ad testandum condicionis equipentis, et nullus concealmentum aut delay permittit.

13) Stricto prohibitur parametros machinae adjustare aut modificare sine doctrina et cognoscentia.

14) Seriously and practically maintain the equipment on time every day according to the operating instructions and true fill the equipment inspection form.

Conditiones utilis CNC lathe

The normal use of CNC lathes must meet the following conditions: the power supply voltage fluctuation at the location of the machine tool is small, the ambient temperature is below 30 degrees Celsius, and the relative temperature is less than 80%.

1 , Requirements for machine tool position environment

The position of the CNC machine tool should be far away from the vibration source, avoiding direct light irradiation and the influence of thermal amplitude, and avoiding the influence of moisture and airflow. Si fuerit fontes vibration is prope instrumentum machinae, anti vibrationis grooves circum instrumentum machinae constituentur. Otherwise, it will directly affect the machining accuracy and stability of the machine tool, causing poor contact of electronic components, resulting in malfunctions and affecting the reliability of the machine tool.

2,Power requirements

Generally, CNC lathes are installed in machining workshops, where the environmental temperature changes greatly and the usage conditions are poor. In addition, there are many mechanical and electrical equipment, resulting in large fluctuations in the power grid. Therefore, the installation of CNC lathes requires strict control of the power supply voltage. The power supply voltage fluctuation must be within the allowable range and kept relatively stable, otherwise it will affect the normal operation of the CNC system.

3,Temperatura conditions

The ambient temperature of the CNC lathe is below 30 degrees Celsius, and the relative temperature is less than 80%. Generally speaking, there are exhaust fans or air coolers inside the CNC control box to maintain a constant operating temperature or minimal temperature difference of electronic components, especially the central processing unit. Temperatura excessiva et humilitas dimittet vitam componentium systemae constituentium et inducet ad incrementum malfunctionum. Magnitudo temperaturae et humilitatis, et magnitudo pulvere, potest causare adhesionem in circuitu integro et ad circulos breves.

4 , Uter instrumentum machinae iuxta instruktiones

Users are not allowed to change the parameters set by the manufacturer in the control system when using CNC machine tools. The setting of these parameters is directly related to the dynamic characteristics of various components of the machine tool. Nunc valores parametros compensationis vacuum iuxta situationem actual adjustari potest.

Utiliores non licet substituere accessorios machinae in voluntate, sicut hydraulic fragmentos, qui excedunt specificationes in manu. When setting up attachments, the manufacturing plant fully considers the matching of various process parameters. Blind replacement can cause mismatches in various parameters and even result in unforeseeable accidents.